Before selecting a CO2 jet machine for an event, confirm the intended cue and direction, mounting position, control workflow, gas connection, and available power. Ask the supplier to verify each point for the exact model being supplied, and keep the relevant product documents with the production plan. This checklist helps event teams turn a creative effect brief into specifications they can review and confirm.
Start with the event and effect requirements
Describe the event format, cue timing, intended effect direction, and how many units may operate together. Share a venue drawing that marks each proposed position, mounting point, cable route, gas-cylinder location, and control desk. Note any access or sightline constraints that could affect placement.
This information gives the supplier context for recommending a configuration. It also helps the production team compare CO2 jet machine specifications with the actual job instead of choosing by appearance or relying on a product-family label. Record the requested effect and unresolved site questions before comparing models.
Compare CO2 jet control options with the show workflow
Ask which control modes the selected model supports, its DMX channel count and channel map, connector type, and trigger behavior. Confirm whether the control arrangement fits the console plan and operator workflow, and clarify what the team needs to know to add the unit to the show file.
MOKA lists DMX512/electronic control and eight DMX channels for the H-C03. Treat these as H-C03 details, not specifications for every CO2 jet machine. Check the current model specification and manual, and confirm control options for the delivered unit before programming cues.
Verify CO2 jet mounting requirements and connections
Confirm the approved mount and aiming method in the manual. Ask which hardware the manufacturer specifies for the selected position, and document the intended direction and mounting point on the venue drawing. Do not assume mounting requirements are identical across models.
For CO2 hose and cylinder compatibility, ask the supplier to identify the connector, hose length, cylinder configuration, and any region-specific adapter required for the supplied model. MOKA notes that tank and connector standards can vary by country on its CO2 product page. Use that as a prompt to verify the actual connection; do not treat a general product-page note as confirmation of a particular cylinder or adapter.
Check the selected unit’s power requirements against the venue supply. H-C03 lists voltage variants and 100 W maximum power. These figures are model-specific examples, not values to apply to another unit. Ask the supplier to confirm the delivered model’s electrical rating.
Plan placement and request model documents
Use the venue drawing to agree on equipment position, hose route, intended direction, cable access, and control-point location. Record each confirmed detail and leave unknown items visibly marked for follow-up. This makes CO2 jet machine mounting and placement requirements specific to the site.
Request the current manual, DMX channel chart, mounting instructions, electrical rating, and written confirmation of CO2 jet machine hose and cylinder compatibility. Match the model number and supplied accessories across the documents. If the manual, product page, and supplier response disagree, ask the manufacturer to resolve the discrepancy before the team finalizes its plan.
A practical review table can keep the information together:
| Check | Confirm with supplier | Record |
| Model and ratings | Exact model, voltage, and power rating | Model document and revision |
| Control | Supported mode, channel count, map, connector, and trigger behavior | Manual or DMX chart |
| Mounting | Approved mount and aiming method | Mounting instructions |
| Gas connection | Connector, hose, cylinder setup, and any adapter | Written model-specific confirmation |
| Event plan | Position, direction, cable and hose routes, and control point | Marked venue drawing |
What should we ask a CO2 jet machine supplier?
Ask for documents that identify the exact model and its control, mounting, electrical, and gas-connection details. Request written clarification for any point that is missing or inconsistent.
How can we confirm hose and cylinder compatibility?
Provide the supplier with the intended cylinder and connection details, then ask them to confirm compatibility for the delivered model and region. Do not infer compatibility from a product-family name.
Why not apply one model’s power or DMX data to the whole range?
Specifications can vary by model. The H-C03 figures are examples for that model only; use the current documentation for the unit being supplied.
A complete CO2 jet machine checklist connects each planned cue to one identified model, its control path, mount, gas connection, power supply, and source documents. Keep open questions with the event brief so the production team can resolve them before finalizing the equipment plan.
📩 Connect with MOKA SFX
Want to pre-book a meeting or inquire about partnership opportunities?
📧 Email us at: info@mokasfx.com
🌐 Visit: www.mokasfx.com


